检索范围:
排序: 展示方式:
Ravindra Nath YADAV, Vinod YADAVA, G.K. SINGH
《机械工程前沿(英文)》 2013年 第8卷 第3期 页码 319-332 doi: 10.1007/s11465-013-0269-3
The effective study of hybrid machining processes (HMPs), in terms of modeling and optimization has always been a challenge to the researchers. The combined approach of Artificial Neural Network (ANN) and Non-Dominated Sorting Genetic Algorithm-II (NSGA-II) has attracted attention of researchers for modeling and optimization of the complex machining processes. In this paper, a hybrid machining process of Electrical Discharge Face Grinding (EDFG) and Diamond Face Grinding (DFG) named as Electrical Discharge Diamond face Grinding (EDDFG) have been studied using a hybrid methodology of ANN-NSGA-II. In this study, ANN has been used for modeling while NSGA-II is used to optimize the control parameters of the EDDFG process. For observations of input-output relations, the experiments were conducted on a self developed face grinding setup, which is attached with the ram of EDM machine. During experimentation, the wheel speed, pulse current, pulse on-time and duty factor are taken as input parameters while output parameters are material removal rate (MRR) and average surface roughness (Ra). The results have shown that the developed ANN model is capable to predict the output responses within the acceptable limit for a given set of input parameters. It has also been found that hybrid approach of ANN-NSGA-II gives a set of optimal solutions for getting appropriate value of outputs with multiple objectives.
关键词: hybrid machining processes (HMPs) electrical discharge diamond grinding (EDDG) artificial neural network (ANN) genetic algorithm modeling and optimization
Recognition of diamond grains on surface of fine diamond grinding wheel
HUO Fengwei, JIN Zhuji, KANG Renke, GUO Dongming, YANG Chun
《机械工程前沿(英文)》 2008年 第3卷 第3期 页码 325-331 doi: 10.1007/s11465-008-0071-9
关键词: topography frequency disturbance filtering analysis wavelength
Ultra-precision ductile grinding of BK7 using super abrasive diamond wheel
ZHAO Qingliang, Brinksmeier Ekkard, Riemer Oltmann, Rickens Kai
《机械工程前沿(英文)》 2007年 第2卷 第3期 页码 350-355 doi: 10.1007/s11465-007-0061-3
关键词: ELID peripheral electrolytic in-process nickel-electroplated monolayer measurement
Investigation on drilling-grinding of CFRP
Yanming QUAN, Wenwang ZHONG
《机械工程前沿(英文)》 2009年 第4卷 第1期 页码 60-63 doi: 10.1007/s11465-009-0008-y
关键词: composites drilling-grinding cemented/plated diamond tool life machined quality
艾兴
《中国工程科学》 2000年 第2卷 第11期 页码 40-51
在机械加工领域,切削加工是应用最广泛的一种加工方法,其发展方向主要是研究髙速切削,对超硬材料加工,主要是发展磨削、超声和放电等高效复合加工技术。文章介绍对髙效切削加工和高效复合加工技术的理论研究和技术开发与应用及所取得的重要成果,主要包括高速切削基础理论、陶瓷刀具材料研究新体系和超硬材料断续磨、超声和电火花的复合加工理论与技术的研究开发。生产实际应用结果表明,高效加工技术可以大幅度提髙加工效率,改善加工表面质量,降低加工成本。
刘广志
《中国工程科学》 2000年 第2卷 第5期 页码 31-33
论述了人造金刚石的发展历程及其在我国的迅猛发展,目前我国的人造金刚石产量已居世界首位。进入20世纪末,人造金刚石新品种不断涌现,CVD、卡邦、世界首颗超厘米级C60单晶也研制成功。
Subsurface damage pattern and formation mechanism of monocrystalline -GaO in grinding process
《机械工程前沿(英文)》 2022年 第17卷 第2期 doi: 10.1007/s11465-022-0677-3
关键词: monocrystalline beta-phase gallium oxide grinding process subsurface damage nanocrystals amorphous phase
Simulation and analysis of grinding wheel based on Gaussian mixture model
Yulun CHI, Haolin LI
《机械工程前沿(英文)》 2012年 第7卷 第4期 页码 427-432 doi: 10.1007/s11465-012-0350-3
This article presents an application of numerical simulation technique for the generation and analysis of the grinding wheel surface topographies. The ZETA 20 imaging and metrology microscope is employed to measure the surface topographies. The Gaussian mixture model (GMM) is used to transform the measured non-Gaussian field to Gaussian fields, and the simulated topographies are generated. Some numerical examples are used to illustrate the viability of the method. It shows that the simulated grinding wheel topographies are similar with the measured and can be effective used to study the abrasive grains and grinding mechanism.
关键词: grinding wheel 3D topographies measurement Gaussian mixture model simulation
Dielectric barrier micro-plasma reactor with segmented outer electrode for decomposition of pure CO
Baowei Wang, Xiaoxi Wang, Bo Zhang
《化学科学与工程前沿(英文)》 2021年 第15卷 第3期 页码 687-697 doi: 10.1007/s11705-020-1974-1
关键词: CO2 decomposition dielectric barrier discharge segmented outer electrodes electrical analysis reactor design
Machinability of ultrasonic vibration-assisted micro-grinding in biological bone using nanolubricant
《机械工程前沿(英文)》 2023年 第18卷 第1期 doi: 10.1007/s11465-022-0717-z
关键词: micro-grinding biological bone ultrasonic vibration (UV) nanoparticle jet mist cooling (NJMC) grinding force grinding temperature
《机械工程前沿(英文)》 2023年 第18卷 第1期 doi: 10.1007/s11465-022-0730-2
关键词: ultrasonic vibration-assisted grinding perforated ultrasonic vibration platform vibration characteristics apparent elasticity method grinding force surface integrity
Mohammadreza SHABGARD, Hamed KAKOLVAND, Mirsadegh SEYEDZAVVAR, Ramin Mohammadpour SHOTORBANI
《机械工程前沿(英文)》 2011年 第6卷 第4期 页码 419-428 doi: 10.1007/s11465-011-0246-7
This paper presents the results of experimental studies carried out to conduct a comprehensive investigation on the influence of ultrasonic vibration of workpiece on the characteristics of Electrical Discharge Machining (EDM) process of FW4 Welding Metal in comparison with the conventional EDM process. The studied process characteristics included the material removal rate (MRR), tool wear ratio (TWR), and surface roughness (Ra and Rmax) of the workpiece after the EDM and ultrasonic assisted EDM (US-EDM) processes. The experiments performed under the designed full factorial procedure and the considered EDM input parameters included pulse on-time and pulse current. The experimental results show that in short pulse on-times, material removal rate in the US-EDM process is approximately quadruple than that of the EDM process. On the contrary, in the long pulse on-times, ultrasonic vibration of work??piece leads to the reduction in the MRR. On the other hand, in short pulse on-times, the TWR in the US-EDM process is lower than that of in the EDM process, and this condition reverses with increase in the pulse on-time. Furthermore, the surface roughness of the workpiece machined by EDM process is slightly lower than that of applied to the US-EDM process.
关键词: electrical discharge machining (EDM) material removal rate (MRR) tool wear ratio (TWR) surface roughness
Modelling of dynamic contact length in rail grinding process
null
《机械工程前沿(英文)》 2014年 第9卷 第3期 页码 242-248 doi: 10.1007/s11465-014-0305-y
Rails endure frequent dynamic loads from the passing trains for supporting trains and guiding wheels. The accumulated stress concentrations will cause the plastic deformation of rail towards generating corrugations, contact fatigue cracks and also other defects, resulting in more dangerous status even the derailment risks. So the rail grinding technology has been invented with rotating grinding stones pressed on the rail with defects removal. Such rail grinding works are directed by experiences rather than scientifically guidance, lacking of flexible and scientific operating methods. With grinding control unit holding the grinding stones, the rail grinding process has the characteristics not only the surface grinding but also the running railway vehicles. First of all, it’s important to analyze the contact length between the grinding stone and the rail, because the contact length is a critical parameter to measure the grinding capabilities of stones. Moreover, it’s needed to build up models of railway vehicle unit bonded with the grinding stone to represent the rail grinding car. Therefore the theoretical model for contact length is developed based on the geometrical analysis. And the calculating models are improved considering the grinding car’s dynamic behaviors during the grinding process. Eventually, results are obtained based on the models by taking both the operation parameters and the structure parameters into the calculation, which are suitable for revealing the process of rail grinding by combining the grinding mechanism and the railway vehicle systems.
关键词: rail grinding contact length dynamic model Hamiltonian system grinding stone rail grinding car
Fiber-reinforced composites in milling and grinding: machining bottlenecks and advanced strategies
《机械工程前沿(英文)》 2022年 第17卷 第2期 doi: 10.1007/s11465-022-0680-8
关键词: milling grinding fiber-reinforced composites damage formation mechanism delamination material removal mechanism surface integrity minimum quantity lubrication
《机械工程前沿(英文)》 2023年 第18卷 第1期 doi: 10.1007/s11465-022-0733-z
关键词: grinding minimum quantity lubrication carbon group nanofluid tribological mechanism
标题 作者 时间 类型 操作
Multi-objective optimization of process parameters in Electro-Discharge Diamond Face Grinding based on
Ravindra Nath YADAV, Vinod YADAVA, G.K. SINGH
期刊论文
Recognition of diamond grains on surface of fine diamond grinding wheel
HUO Fengwei, JIN Zhuji, KANG Renke, GUO Dongming, YANG Chun
期刊论文
Ultra-precision ductile grinding of BK7 using super abrasive diamond wheel
ZHAO Qingliang, Brinksmeier Ekkard, Riemer Oltmann, Rickens Kai
期刊论文
Dielectric barrier micro-plasma reactor with segmented outer electrode for decomposition of pure CO
Baowei Wang, Xiaoxi Wang, Bo Zhang
期刊论文
Machinability of ultrasonic vibration-assisted micro-grinding in biological bone using nanolubricant
期刊论文
characteristics and machining performance of a novel perforated ultrasonic vibration platform in the grinding
期刊论文
Ultrasonic assisted EDM: Effect of the workpiece vibration in the machining characteristics of FW4 Welded Metal
Mohammadreza SHABGARD, Hamed KAKOLVAND, Mirsadegh SEYEDZAVVAR, Ramin Mohammadpour SHOTORBANI
期刊论文
Fiber-reinforced composites in milling and grinding: machining bottlenecks and advanced strategies
期刊论文